Carry eight single function calibrators plus a milliamp calibrator with loop supply in the palm of your hand! Sources & Reads mA, T/C, RTD, V, mV, and Frequency. Also Sources pH, accepts wide range of PIE Digital Pressure Modules, has Loop Diagnostic Capabilities with Patented Current Leakage Test. Includes rubber boot, leads, hands free Carrying Case and FREE NIST Traceable Calibration Certificate.
Lighten up your toolbox Compact calibrator replaces toolbox of single function devices Milliamp • Voltage • Frequency • pH Thermocouples • RTDs • Pressure • Troubleshooter
First multifunction calibrator with three troubleshooting tools Troubleshoot loop problems - Quickly diagnose ground fault and current leakage with patented Loop Diagnostic technology. Automatically detect 2, 3 or 4 wire RTDs - Trouble shoot sensor connections and find broken wires with patented technology. Troubleshoot wiring problems - Beep with continuity checker.
Lighten up your toolbox Compact calibrator replaces toolbox of single function devices Milliamp • Voltage • Frequency • pH Thermocouples • RTDs • Pressure • Troubleshooter
Simulate pH probes & calibrate pH transmitters Source from 0.000 to 14.000 pH @ 25 degrees C (77 degrees F) into transmitters & analyzers corresponding to -414.12 to +414.12 mV
Technician friendly operation Intuitive EZ-DIAL Double Click Menu makes it easier to setup than other multifunction calibrators. Same as the single function PIE Calibrators.
Calibrate 2 wire transmitters - control input & monitor output Simulate transmitter inputs while powering it with the internal isolated 24 V supply & measuring the 4-20 mA output. Dual display of transmitter input & output. Simplify HART hookups with built-in 250 Ohm resistor
Use it as a milliamp and voltage calibrator Source 0 to 24.000 mA, 0 to 10.250 V dc, -20.000 to 99.999 mV and -500.00 to 999.99 mV. Read to 24.000 mA, 60.00 V dc -99.999 to +99.999 mV and -999.99 to +999.99 mV. Simulate 2-Wire Transmitters.
Calibrate directly in temperature to 0.1 degrees C & 0.1 degrees F Compatible with the instruments you use including all brands of smart transmitters and PLCs with 14 thermocouple & 9 RTD types.
Checkout flow & vibration systems To 2000 CPM (Counts-Per-Minute), 999.99 Hz, 9999.9 Hz & 20.000 kHz.
Measure pressure with optional pressure modules 32 modules for gauge, differential, absolute & compound pressure
Easy to read Turn on the backlight & easily see the display in dark areas of the plant
Quickly set any three outputs plus automatic stepping & ramping Easily set any value quickly with the adjustable "DIAL" plus store any three output settings for instant recall with the EZ-CHECK™ switch. Choose between 2, 3, 5 & 11 steps to automatically increment the output in 100%, 50%, 25% or 10% of span. Select RAMP to smoothly increase and decrease the output between Zero and Span. Set step/ramp time to match your system from 5, 6, 7, 8, 10, 15, 20, 25, 30 and 60 seconds.
Measure temperature sensors, frequency pickups, loop currents, voltage levels & pressures Check the values of your process sensors. Instantly recall MAX and MIN values to see process variability
Advantages of the PIE 830 over the Altek 830
Higher Accuracy Accurate to 0.006 mA, Pt 100 Ohm RTD to 0.2°C/0.4°F, Type K to 0.3°C/0.6°F, pH to 0.003 pH
Loop Diagnostics - Unique to PIE Only multifunction calibrator that can power up a loop and tell you that there is moisture, corrosion or a ground fault causing current to leak to ground.
Simulates a pH probe Calibrate pH tranmitters & analyzers before attaching probe to verify that each is working correctly.
Isolated internal 24 V loop supply Calibrate 2-wire transmitter with electrical isolation between the input and the output for more accuate and stable readings.
Wider range of pressure modules & scales Choose from 32 different modules with up to 32 engineering units for greater compatability with your processes.
Works with more instruments Compatible with smart transmitters, multichannel recorders, PLCs and DCSs - GUARANTEED! More Thermocouple & RTD ranges with 0.1° resolution and better accuracy.
Smaller & lighter Pocket sized and easier to carry
LED for optical pickups LED flashes green in sync with frequency output. Illuminates red for overload conditions.
Easier to hook-up Diagrams are shown on the display indicating where to plug in the test leads.